Morton M340012 Bedienerhandbuch PDF herunterladen (Seite 22)

22 Morton

System Saver

Installation & Operation Manual

Troubleshooting

Need help troubleshooting? Call Toll Free 1-888-64 WATER (1-888-649-2837)

Monday- Friday, 8 AM - 7 PM EST or visit www.systemsaver.com

When you call, please be prepared to provide the model and serial number,

found on the rating decal, located on the rim below the salt lid hinges.

Resetting to Factory Defaults

To reset the electronic controller to its factory default

for all settings (time, hardness, etc.):

1. Press the SELECT button and hold it until the dis-

play changes twice to show “CODE” and the flash-

ing model code.

2. Press the

UP button (a few times, if necessary)

to display a flashing “SoS”.

3. Press the SELECT button, and the electronic con-

troller will restart.

4. Set the present time, hardness, etc., as described

on pages 13 & 14 (for Models M20, M27 & M30) or

pages 16 & 17 (for Model M34).

FIG. 47

Model M34Models M20, M27 & M30

This check verifies proper operation of the valve

motor, brine tank fill, brine draw, regeneration flow

rates, and other controller functions. Always make

the initial checks, and the manual initiated diagnos-

tics.

NOTE: The electronic control display must show a

steady time (not flashing). If an error code

shows, first press the SELECT button to enter

the diagnostic display.

1. Press the RECHARGE button and hold in for 3

seconds. RECHARGE begins to flash as the soft-

ener’s valve advances from the service to fill posi-

tion. Remove the brinewell cover and, using a

flashlight, observe fill water entering the tank.

Manual Advance Regeneration Check

If water does not enter the tank, look for an

obstructed nozzle, venturi, fill flow plug, brine tub-

ing, or brine valve riser pipe.

2. After observing fill, press the RECHARGE button to

move the softener’s valve into the brine position. A

slow flow of water to the drain will begin. Verify

brine draw from the brine tank by shining a flash-

light into the brinewell and observing a noticeable

drop in the liquid level. This may take 15 to 20

minutes.

NOTE: Be sure water is in contact with the salt, and

not separated by a salt bridge (See "Breaking

A Salt Bridge" section).

If the water softener does not draw brine, check for

(most likely to least likely):

= Dirty or plugged nozzle and venturi, see

"Cleaning the Nozzle and Venturi" section.

= Nozzle and venturi not seated on the gasket, or

gasket deformed.

= Valve seals leaking.

= Restriction in valve drain, causing a back-pres-

sure (bends, kinks, elevated too high, etc.). See

"Install Valve Drain Hose" section.

= Obstruction in brine valve or brine tubing.

NOTE: If water system pressure is low, an elevated

drain hose may cause back pressure, stop-

ping brine draw.

3. Press the RECHARGE button to move the soften-

er’s valve into the backwash position. Look for a

fast flow of water from the drain hose. Check that

the drain can adequately handle the flow and vol-

ume.

An obstructed flow indicates a plugged top distribu-

tor, backwash flow plug, or drain hose.

4. Press the RECHARGE button to move the soften-

er’s valve into the fast rinse position. Again look

for a fast drain flow. Allow the softener to rinse for

a few minutes to flush out any brine that may

remain in the resin tank from the brining cycle test.

5. To return the softener’s valve to the service posi-

tion, press the RECHARGE button.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27

Kommentare zu diesen Handbüchern

Keine Kommentare

Morton M340012 Bedienerhandbuch Seite 22

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Wasserspender Morton M340012